بستن

safeland.ir@gmail.com       +98 21 88 81 48 12

Tag Archive for: Epson Powerlite 915W Projector Lamp Ballast Replacement

توسط

Epson Powerlite 915W Projector Lamp Ballast Replacement

Introduction

When three red lights start blinking on the LED display of these projectors, it often means the lamp ballast has gone bad. This will show you how to replace the ballast.

Step 1 Remove the bulb

 
Image 1/3: While here, be sure to remove the 2 screws to the right of the lamp.Image 2/3: While here, be sure to remove the 2 screws to the right of the lamp.Image 3/3: While here, be sure to remove the 2 screws to the right of the lamp.

 

 

This is a standard procedure. Take off the cover, loosen the lamp screws and pull the lamp straight out.

 
 

While here, be sure to remove the 2 screws to the right of the lamp.

 
 

Step 2 Removing the Filter

 
Image 1/3: Pull the filter straight out.Image 2/3: Be sure to leave the filter door open as it will hold the projector case closed if it is closed.Image 3/3: Be sure to leave the filter door open as it will hold the projector case closed if it is closed.
 

Slide the notch to the right and then open the filter area.

 
 

Pull the filter straight out.

 
 

Be sure to leave the filter door open as it will hold the projector case closed if it is closed.

 
 

Step 3 Opening the Case

 
Image 1/3: Remove 5 screws from back panel. These are all the same as well (not the same as the ones on the bottom).Image 2/3: Lift the panel off.Image 3/3: When reassembling, it helps to save this step for after the top of the case is back together.
 

Remove 7 screws from the bottom. These are all the same size and thread.

 
 

Remove 5 screws from back panel. These are all the same as well (not the same as the ones on the bottom).

 
 

Lift the panel off.

 
 

When reassembling, it helps to save this step for after the top of the case is back together.

 

Step 4 Remove the Ribbon Cable

 
Image 1/2: Image 2/2:

 

 

Disconnect the ribbon cable connected to the LEDs on the outside of the case.

 
 

Step 5 Remove Lamp Area Bezel

 
Image 1/2: Lift the bezel straight up.Image 2/2: Lift the bezel straight up.

 

 

There are 5 screws in this area that need removed. 3 are the same and then there are 2 others that are each unique (marked with blue and green).

 
 

Lift the bezel straight up.

 

Step 6 Moving the Fan and Vent

 
Image 1/3: Pull wires off top of the vent and out of the channel to the side of the vent.Image 2/3: When you lift the fan, it will all come up as one piece, but still have wires connected. You donImage 3/3: When you lift the fan, it will all come up as one piece, but still have wires connected. You don

 

 

Remove 2 screws from the vent.

 
 

Pull wires off top of the vent and out of the channel to the side of the vent.

 
 

When you lift the fan, it will all come up as one piece, but still have wires connected. You don’t need to remove the whole unit, just movie it to the side. You will have to wiggle it out from under the cable that crosses over the top of it.

 

Step 7 Set Fan and Vent Assembly to the side

 
Image 1/1:
 

 

 

Move the assembly out of the way.

 

Step 8 Unscrew Lamp Ballast

 
Image 1/2: Image 2/2:
 

Remove the 2 screws from the front and back of the lamp ballast holder.

 
 

Step 9 Disconnect the Ballast

 

Image 1/3: Now you can slide the ballast out of the holder and disconnect the remaining 2 connections.Image 2/3: Now you can slide the ballast out of the holder and disconnect the remaining 2 connections.Image 3/3: Now you can slide the ballast out of the holder and disconnect the remaining 2 connections.

 

Lift the ballast and holder up in the back and slide it to where the blue plug is visible and then disconnect it.

 

 

Now you can slide the ballast out of the holder and disconnect the remaining 2 connections.

سایت فروشگاهی